Recent content by KrazyK-nampa

  1. KrazyK-nampa

    95 Chevy 4x4 reduced engine power

    95 or 05???
  2. KrazyK-nampa

    Outlook Acadia Traverse...best way to remove engine

    Lol it can be done with a cherry picker, as bad as I hate to admit it I have pulled off this horrendous feat. Expect a good week at it! You will need a heavy duty base with wheels to set the engine cradle on as you lift body off. Its really not easy, if you aren't turning wrenches on the...
  3. KrazyK-nampa

    92 S10 Blazer TBI Rich

    Thats a bummer bro, but as they stressed to us in college... "Haste makes Waste" if you try to shortcut you typically end up in a worse situation than you started in, as painful as it sounds its best to take your time. Depending on type of gasket you may b able to reuse but if a tinybit gets...
  4. KrazyK-nampa

    92 S10 Blazer TBI Rich

    You sure you set valves right on #5?
  5. KrazyK-nampa

    92 S10 Blazer TBI Rich

    Did you rebuild heads while off?
  6. KrazyK-nampa

    03 Impala 3.8L hole in upper intake

    Yes EricC, found 4 ripped injector o-rings in process, customer changed maf trying to kill po171 & po174 codes previous to this situation also
  7. KrazyK-nampa

    03 Impala 3.8L hole in upper intake

    So culprit found: catylitic convertor was plugged causing excessive heat on upper plenum thru egr tube, burning a hole completely through plenum. Unfortunately the car has California emissions so convertor cost an arm & a leg (thats even a universal weld in). But got it all taken care of: new...
  8. KrazyK-nampa

    87 built 318 falls on face

    Well returned the truck today, and gotta say a few tears built up in my eyes[emoji24]. Was hard to see her go but as the saying goes... Love to watch her leave. Customer was thrilled w/performance of truck upon retrieval. Once again i really appreciate the help.... A mind boggler like this is...
  9. KrazyK-nampa

    87 built 318 falls on face

    This truck leaves for colorado tomorrow not sure what their emissions are but would have to assume its pretty comparable to ours. I cant really go "stock" unfortunately it came with a 2bbl factory but cust. put 4bbl on before bringing it to me. I know this is frustrating but seems like its...
  10. KrazyK-nampa

    87 built 318 falls on face

    Ok now i am getting about 5 psi. But if computer changes timing thru single connector, wont it still fight the vac adv system i put on it(even w/vac disc @ esc)?
  11. KrazyK-nampa

    87 built 318 falls on face

    Ok got fuel press. And somehow its reading 1 psi if i kink hose or put it in gear, otherwise its reading 0psi at idle.... Gonna change pump. This system should b at 7-9 psi if i remember correctly (please correct me if im wrong)
  12. KrazyK-nampa

    87 built 318 falls on face

    LynnM: yes auto (havent messed w/trans at all) but have redone both diffs
  13. KrazyK-nampa

    87 built 318 falls on face

    Single port egr. But had same symptoms b4 drilling manifold to accept egr
  14. KrazyK-nampa

    94 suburban k2500 454cid stumbles after changing egr valve

    Ok got her figured out, after replacing egr and iac, the stupid tps was out of whack causing the stumble. Checked fuel pressure during stumble was 37psi so didnt mess w/ tb rebuild but did change fuel filter.Repositioned tps and got rid of stumble and backfire.... Off to shoot my buck in the...
  15. KrazyK-nampa

    94 suburban k2500 454cid stumbles after changing egr valve

    Changed fuel filter and have little better response. Damn hard fuel lines dont make it easy 2 put fuel press tstr on.